double glazing repairers Glazing Door Lock repairs to double glazed windows

Are your uPVC door or window mechanism faulty? Perhaps the window or door handles don't meet up properly or are hard to use.

You'll be wasting energy in the event that your double glazed window repair-glazed doors fail to function properly. This increases the chance of burglary. Owen the Locksmith will be able to repair your door lock for reasonable costs.

Snapped Key

When a key snaps off within the lock, it can be incredibly frustrating. It also poses a security risk since the door may not lock and could leave you vulnerable to intruders. There are a few quick solutions you can use to resolve the issue and make your door work again.

Be sure to remain calm. If you panic and begin poking around wildly, you might just end up pushing the broken piece of the key deeper into the lock, thereby making the situation much worse.

Spray WD-40 or another penetrating oil, into the lock. This will allow the broken piece come out more easily. You can also use the screwdriver to break any pieces stuck. If you're fortunate enough to have a little bit of the key left sticking out, you can make use of a paperclip, or any other metal object that is thin to grab it and remove it. Both methods work, but be careful not to push the broken key piece further into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades are also well for this. If you don't have any of these handy, you can make use of needle-nose pliers to bend them and create a hook. Finally, a pair of tweezers is a good way to grasp and pull out the remaining part of the broken key.

If you are unable to remove the broken key piece Use a lock deicer. It is available in most hardware stores and works by freezing any moisture present inside the lock.

If none of these solutions work, it might be time to consult a locksmith. The experts at Fitlocks can quickly fix problems such as broken handles or snapped keys with uPVC locks and door mechanisms. They can also reconfigure your double glazing door mechanisms to make them more user-friendly. Get a Double Glazed repairs glazing repair double glazing window through us online, or give us a call to discuss your requirements.

Broken Cylinder

A broken cylinder can be a major security risk. It's fortunately a simple repair for a professional locksmith to complete. A locksmith must tap the cylinder to repair it. This can be done with a hammer or other tool. However, the most effective method is to use a wire or a long match. Position the match or the wire's end close to the keyway. After that, the locksmith can hit the lock to break it open. This is much better than using a hammer that can damage the lock.

Overheating is the main reason behind cylinder heads cracking. This can happen when the cylinder block as well as the cylinder head are made of different metals, such as cast iron and aluminium. When different metals heat up and cool down at different rates, it could cause localised hotspots that expand faster than the rest of the cylinder head, leading to cracks.

Another possible cause for cracks in cylinders is corrosion. When the cylinder head and the block of the cylinder are not properly maintained, it can result in corrosion or rust that could cause them to expand at a greater rates than they ought to. This can cause cracks in the future.

If your uPVC window or door lock is brittle and requires a lot more pressure to turn, it could be due to a variety of reasons. A defective locking mechanism, misalignment, or a worn handle are common causes of this problem.

This is a straightforward and affordable fix that the majority of homeowners with double glazing can perform. A professional locksmith will usually be able solve this issue within a matter of hours of arriving at your home. Depending on your needs they can change the locking mechanism, change the window handles, and change the gearboxes. A professional locksmith will be able to advise you of the most cost-effective option for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders, which provide an additional layer of protection from burglars. It is a small cost to enjoy the peace of mind that comes from knowing your uPVC door is secured.

Broken Handle

It's not surprising that window handle locks may break. They have intricate mechanisms that become less effective over time. If yours is damaged it's difficult to determine the source of the problem and make sure you fix it correctly.

Fixing your broken handle, whether it's the internal latch or locking mechanism can increase the security of your uPVC door and reduce the risk of draughts. It is costly to repair or replace your handle incorrectly and it can also damage the frame and the lock of your door.

Screwdriver: With the window open, loosen the screw holding the handle. The screw should be on the inside of the backplate, usually hidden by an eye-catching cap to conceal it for aesthetic reasons. Be sure to not lose any of the internal components within the handle, for example the levers or plates on either side of the spindle. Keep them in the same order so that it is simpler to replace them in the event of a need.

Next, turn the handle to make it 90 degrees towards the window frame. Then, loosen the screw at the back of the handle which holds it to the internal spindle by using another screwdriver. Once the screw is loose, you should be capable of pulling the handle off and take out the broken spindle. Replace it with a new spindle, ensuring it's the same length (you can find them online or in hardware stores). Securely screw it into place. Be careful not to tighten too much as this could cause damage to the handle or the window frame.

Make sure the new handle is correctly installed, then close and test the handle. It should work smoothly and you'll be able to open your window once more.

Make sure to check that your uPVC window is closing properly while you're working with the handle. If they're not, you could experience damp and draughts in your home, as well as compromising the efficiency of your home's energy usage. Core Sash Windows is a local window company that can alter the hinges of the window frames to ensure they close correctly.

Broken Spindle

It is usually the case that the spindle within a handle breaks rather than the handle itself. This is especially typical in uPVC tilt and turn windows. These types of windows require a handle that is a lock mechanism that is located in the frame of the window. The handle is attached to a centre rod that in turn activates cams that resemble mushrooms, which locks are inserted into the window frame. If the dead latch mechanism does not open when the handle is turned, it is likely that the spindle has broken, this can be a frustrating problem.

Luckily, there are steps that can be taken to fix this problem. A reputable locksmith can swiftly and efficiently solve the issue. They will be able to disassemble the window handle by using a tool that can remove the wheel component of the mechanism that is where the spindle is. This is done without damaging the handle or causing any other damage to the frame of the window.

After the wheel has been removed, the technician will examine the spindle to determine what has caused it to break. This involves breaking the spindle into its individual components and carefully observing their general condition as well as any specific areas of wear or damage. This procedure is typically carried out by technicians in a clean environment.

The next step is to clean the damaged spindle. This assists in removing any debris or dirt that could be hindering its normal operation. The spindle may be replaced or repaired. If it's being replaced, the technician could use the dowel that is similar in size to the one used in the first and drill mating holes in both pieces of the spindle. This will ensure that the spindle fits perfectly with the handle.

If the spindle that is damaged is beyond repair double glazing windows, it could be necessary to replace it completely. Home centres sell generic replacements but If the style of your window is unusual then it will be necessary to contact a wood worker or cabinet maker who can replicate the exact model for you. Once the new spindle is installed, it can be fitted to the handle by lining up the screw holes in the handle with the frame's existing screws. Once the handle is in place, you can use your uPVC windows.