Cat flaps let your pet move around whenever they want without you having to let him in or out. They also can help stop your cat from peeing in the home.

It is easier to install a cat flap on a Upvc panel than one made of glass but you'll require some knowledge and appropriate tools.

Measure the Door

fitting cat flap in upvc door panel a cat flap in the door can be a challenge but if you use the correct type of cat flap make sure you take your time and follow the directions provided, it should not prove to be too much trouble. We will help you draw the shape and then use a jigsaw in order to cut the door area. Then we will finish the job by attaching the cat flap insulation flap. This will ensure that the flap remains in place and protects the door from rain and wind causing damage.

The first thing you need to do is determine the width of your pet to get a precise measurement of the size of cat flap you will need. This will let you select a flap that is large enough to allow your pet to enter the home and exit without needing to open the door each time.

If your kit comes with an illustration of where to drill then you can stick it on the door, and then draw a pencil around it. If your door has a sill or moulding at the bottom, be sure you leave plenty of space between your cat and the moulding or sill.

Then put on your eye protection and a dust mask, and using a jigsaw begin to cut along the line you penciled in, but don't push the blade too hard because this will cause it to cut more quickly than you want it to. Use a set square to ensure that you are cutting the material in a proper manner and that the cut is a rectangle shape. Once you are satisfied with the result, you are able to remove the remaining door material.

Draw a Line

The cat flap is a great method to let your pet out and in without having to worry about them being a nuisance to guests or leaving unwanted gifts in the home. It also prevents drafts and helps to keep the temperature inside your home in a stable manner. The installation of a cat flap your door may seem daunting for those who haven't attempted it before. A lot of people will hire an expert carpenter or joiner to do the work. It is an option, but you can do it yourself, provided the tools are appropriate and the steps are followed.

While this is far easier to do with a wooden door, it is still possible in uPVC doors, but you need to be very careful not to scratch the doors, as this can cause damage to your warranty. The first step is to measure the door to make sure it will accommodate the new cat-flap. This isn't too difficult for a standard uPVC door, however you might need to take extra care if you are using an alternative kind of door, as they can be more difficult to cut than solid uPVC panels.

Next, you will need to determine the belly height of your cat. This is the measurement from the floor to the lower part of the cat's stomach and you'll need find a place in the door that will be within the range your cat can comfortably pass through. Once you know this you'll have to draw the area with an eraser and a spirit level to ensure that the hole you will make will be a good fit for your cat.

Once you've marked the area, you're now ready to cut the hole. It is crucial to take your time and use a jigsaw in order to ensure that the cuts are clean and smooth not uneven and rough. This could cause damage to your door. You should also remember to wear safety glasses and a dust protection mask at all times when working with the jigsaw as dust from the saw can be dangerous to your health. After you've finished the cutting, you will have to smooth out the edges of the hole using sandpaper so that your cat flap in bifold doors flap will fit easily in place.

Make a hole

Getting a cat flap fitted into an existing door panel or double glazing sealed unit is quite difficult. If you're not proficient in DIY, it is recommended to hire a professional to do the work for you. A botched job could not only look ugly but also pose security risks. It could allow cold air to enter when the cat is outside and hot air out when inside.

The first thing you have to do is mark out the location of the hole in the door using an eraser and a spirit level. This will ensure that it is properly positioned and that it runs in a straight line with the other components of the door. Make sure to have sandpaper to smooth out any rough edges.

Wear any safety equipment you need to work with the power tool. If you are concerned about the noise of a jigsaw you can buy one that is cordless, which is much quieter and easier to use.

It is crucial to only remove the material required for the fitment of the cat flap. It is necessary to leave a bit of material for the wall thickness of the flap. However cutting away too much could cause problems or even damage the frame of the door.

If the door is made of upvc and features a metal panel or frame, it may interfere with the microchip flap. In this scenario you'll need create an extra-large hole to ensure that the metal does not get in contact with the walls of the flap.

If you're installing an animal flap to the frame of a double-glazed window cat flap with a metal frame then you will need to speak to a professional who can provide you with a new pane of glass with the hole for the cat flap premade in it. It is much less expensive to do this than to attempt to fix a cat flap into an existing pane of glass that was not designed specifically for the purpose.

Fit the Flap

Cat flaps let your pet come and go at their own pace, giving them the freedom to relax in the home whenever they feel like it. However, if you have an uPVC door, it may be difficult to put in a Cat Flap bifold doors flap, especially if you don't own a glass pane that can be cut for one. If you're looking to install a half-glazed uPVC replacement panel, it is possible to add an additional cat flap. It's not as simple as just cutting a hole in the door though and there are some things you'll need to take care of first to make sure it's safe.

A uPVC, GRP or composite door panel usually has an flimsy plastic outer layer joined to a soft insulating polystyrene core. It is essential to be cautious when cutting the material. This type of door usually comes with a template drawing which you can use as a guide for cutting the hole in your door.

After you have marked out the hole in your front door, it's time to put in the cat flap. You can buy and fit various models, from basic push-button operated ones to ones that are activated by microchips that allow only your pet. Whatever type of cat flap you pick it's essential that your cat is able to utilize the flap with ease without getting stuck outside in bad weather.

It's a good idea to choose circular fittings rather than one that is square, since circles are more securely cut into door glass. This is because square holes are more likely to break the glass when drilled. It's also a safer option to use as you're not at risk of drilling into toughened glass that could shatter and cause injury to your pet or your family. This is particularly important if there are elderly or children living in your home that might be injured by glass shards.